learn
9 years ago
I have Vector VN1630 box. On one side it has Two serial 9-pin mal
connectors. One 9-pin male connector is labeled CH 1/3. The other 9-pi
male connector is labeled CH 2/4. I connect my target Electronic Contro
Unit (ECU) to CH 2/4 connector.
From Control Panel - I open Vector Hardware Config. I expand on VN163
tab. Then, I click on On board CAN. It shows Two assigned applications
CANoe and CANFlash, both on CAN 1. Under D-SUB9 Pin Assignment, it says
Connector CH 2/4. What does this mean that CAN applications are on CA
1 but CAN bus is connected to CH 2/4 ? Some of my CAN applications don'
appear under VN1630 but they work with VN1630 ?
I have several CAN based applications installed in my computer a
follows:
1. In-house CAN based software tool for monitoring DC motor speed an
positions. This tool doesn't go through Vector VN1630 Box. It has it'
own CAN Hardware, PCAN-USB. Maybe that's why I don't see any CAN channe
assignment in this software tool ?
2. Vector CANoe - I invoke vector CANoe. From main menu, I go t
Configuration - Network Hardware. Some of the things I see is CAN Channe
1, CAN 1. I click on Options - Activate CAN 2 with same baud rate i
selected.
CANoe main menu, I go to Configuration - I/O Hardware - Vector I/O -
it says I/O Piggy (1) is disabled. What is I/O Piggy? Why might it b
disabled? When should it be enabled?
From CANoe main menu, I go to Configuration - Options - Under Channe
Usage, it says CAN 1.
3. Few other in-house CAN based software tools - On one of these CA
Applications, when I select CH2, it says VN1630 Channel 2 in Green Color.
This application operates through VN1630 D-SUB9 CH 2/4. What is CH 2/4 ?
CH 2 or CH 4? Why doesn't this application need to be listed in Vecto
Hardware VN1630 under Control Panel like CANoe and CANFlash are listed
--------------------------------------
Posted through http://www.EmbeddedRelated.com
connectors. One 9-pin male connector is labeled CH 1/3. The other 9-pi
male connector is labeled CH 2/4. I connect my target Electronic Contro
Unit (ECU) to CH 2/4 connector.
From Control Panel - I open Vector Hardware Config. I expand on VN163
tab. Then, I click on On board CAN. It shows Two assigned applications
CANoe and CANFlash, both on CAN 1. Under D-SUB9 Pin Assignment, it says
Connector CH 2/4. What does this mean that CAN applications are on CA
1 but CAN bus is connected to CH 2/4 ? Some of my CAN applications don'
appear under VN1630 but they work with VN1630 ?
I have several CAN based applications installed in my computer a
follows:
1. In-house CAN based software tool for monitoring DC motor speed an
positions. This tool doesn't go through Vector VN1630 Box. It has it'
own CAN Hardware, PCAN-USB. Maybe that's why I don't see any CAN channe
assignment in this software tool ?
2. Vector CANoe - I invoke vector CANoe. From main menu, I go t
Configuration - Network Hardware. Some of the things I see is CAN Channe
1, CAN 1. I click on Options - Activate CAN 2 with same baud rate i
selected.
CANoe main menu, I go to Configuration - I/O Hardware - Vector I/O -
it says I/O Piggy (1) is disabled. What is I/O Piggy? Why might it b
disabled? When should it be enabled?
From CANoe main menu, I go to Configuration - Options - Under Channe
Usage, it says CAN 1.
3. Few other in-house CAN based software tools - On one of these CA
Applications, when I select CH2, it says VN1630 Channel 2 in Green Color.
This application operates through VN1630 D-SUB9 CH 2/4. What is CH 2/4 ?
CH 2 or CH 4? Why doesn't this application need to be listed in Vecto
Hardware VN1630 under Control Panel like CANoe and CANFlash are listed
--------------------------------------
Posted through http://www.EmbeddedRelated.com